Home › Compliance › BTEX Emissions and Thermal Oxidizers for Natural Gas Processing

BTEX Emissions and Thermal Oxidizers for Natural Gas Processing

BTEX is a common abbreviation for benzene, toluene, ethylbenzene, and xylene. These aromatic hydrocarbons may be present in raw natural gas and associated hydrocarbon liquids. In gas conditioning equipment, small amounts of BTEX may be absorbed into glycol or amine streams and later released with regenerator overhead vapors or acid gas streams.

Thermal oxidizers are one equipment option used to handle certain hydrocarbon-bearing vapor streams from gas processing equipment. In applications involving TEG dehydration units, amine treating units, and related gas conditioning equipment, thermal oxidizers may be considered as part of the overall emissions control approach.

Actual emissions requirements depend on the facility, gas composition, throughput, equipment configuration, permit conditions, jurisdiction, and applicable regulations. This article is a general equipment-focused overview, not a substitute for environmental or regulatory review.

What Is BTEX?

BTEX compounds are naturally occurring aromatic hydrocarbons. They can be present in crude oil, condensate, produced liquids, and natural gas streams. Benzene is often the most closely watched compound because of health and environmental concerns.

In gas processing and conditioning systems, BTEX behavior depends on:

  • Gas composition
  • Hydrocarbon liquid content
  • Glycol or amine circulation rate
  • Operating pressure and temperature
  • Regenerator design
  • Still column or overhead configuration
  • Facility emissions profile
  • Control device requirements

Because these conditions vary by site, BTEX emissions should be evaluated from project-specific process data.

Where BTEX Emissions Can Occur

BTEX emissions may be associated with several types of gas conditioning equipment, especially where solvents contact hydrocarbon-bearing gas streams.

TEG Dehydration Units

TEG dehydration removes water vapor from natural gas using triethylene glycol. In addition to absorbing water, glycol can absorb small amounts of hydrocarbons, including BTEX compounds, depending on the gas composition and operating conditions.

During regeneration, rich glycol is heated so absorbed water can be removed. Hydrocarbons absorbed into the glycol may be released in the regenerator overhead stream along with water vapor and stripping gas if used.

For this reason, emissions review is often part of TEG dehydration system design, especially for larger units, higher-BTEX gas streams, or facilities with specific permit requirements.

Amine Treating Units

Amine treating units remove H2S and CO2 from sour gas. Depending on the gas composition and solvent behavior, some hydrocarbons may enter the amine system and be released with regenerator overhead or acid gas streams.

BTEX emissions from amine systems are typically evaluated based on the gas stream, solvent selection, acid gas handling method, and overall facility configuration. In some projects, the amine unit, dehydration unit, and other process equipment are reviewed together to understand the full emissions profile.

Regulatory and Permit Considerations

Environmental requirements for BTEX, hazardous air pollutants, volatile organic compounds, and control devices are facility-specific. In the United States, requirements may involve federal rules, state regulations, local air district requirements, and site-specific permit conditions.

Factors that can affect requirements include:

  • Facility classification
  • Potential to emit
  • Actual emissions
  • Dehydrator size and throughput
  • Gas composition
  • HAP and VOC content
  • Existing control devices
  • Permit limits
  • Jurisdiction
  • Recordkeeping and monitoring requirements

Some facilities may be required to control emissions from glycol dehydrators or other equipment. Other facilities may evaluate controls as part of permitting, emissions reduction, or project design. The correct approach should be confirmed with qualified environmental and regulatory professionals.

How Thermal Oxidizers Work

A thermal oxidizer is a combustion device designed to oxidize combustible vapors at elevated temperature. Hydrocarbon-bearing vapor streams are routed to a combustion chamber, where the vapors are mixed with combustion air and heated in a controlled environment.

For gas processing applications, a thermal oxidizer may be used to handle vapor streams associated with:

  • TEG dehydration still column overheads
  • Amine regenerator overhead or acid gas streams
  • BTEX-bearing vapors
  • Certain waste gas streams
  • Other project-specific vent streams

Thermal oxidizer performance depends on the vapor composition, flow rate, heating value, combustion temperature, residence time, mixing, burner design, controls, and monitoring requirements.

Common Thermal Oxidizer Components

A thermal oxidizer package may include:

  • Combustion chamber
  • Burner system
  • Fuel gas train
  • Combustion air system
  • Flame safety controls
  • Temperature monitoring
  • Stack
  • Control panel
  • Instrumentation
  • Piping connections
  • Shutdown and alarm functions

The exact configuration depends on the application, vapor stream, fuel source, site conditions, code requirements, and permit or monitoring requirements.

When a Thermal Oxidizer May Be Considered

A thermal oxidizer may be considered when a facility needs to handle combustible or hydrocarbon-bearing vapors from gas conditioning equipment. The need for a thermal oxidizer depends on process and regulatory factors, not simply the presence of a dehydrator or amine unit.

Common reasons to evaluate a thermal oxidizer include:

  • BTEX or VOC-bearing vapor streams
  • Dehydrator still column emissions
  • Amine unit overhead or acid gas handling
  • Permit-driven emissions control requirements
  • Facility emissions reduction objectives
  • Integrated gas conditioning packages
  • Project-specific customer or jurisdictional requirements

Before selecting a thermal oxidizer, the project team should review vapor flow rate, composition, BTEX or VOC content, H2S content if present, heating value, operating schedule, monitoring needs, and applicable requirements.

Monitoring and Documentation Considerations

Thermal oxidizers may require monitoring and documentation depending on the facility requirements and applicable regulations. The specific monitoring approach should be based on the permit, control device design, and regulatory review.

Common monitoring and documentation considerations may include:

  • Flame detection
  • Combustion chamber temperature
  • Burner status
  • Fuel gas pressure
  • Operating hours
  • Shutdowns and alarms
  • Maintenance records
  • Calibration records
  • Stack testing or performance testing when required

These requirements can vary significantly. The correct monitoring package should be coordinated with the project’s environmental and controls requirements.

Thermal Oxidizer Design Considerations

Thermal oxidizer design starts with the vapor stream. Important inputs include:

  • Vapor flow rate
  • Vapor composition
  • BTEX or VOC content
  • Water vapor content
  • H2S or acid gas content, if present
  • Heating value
  • Required control performance
  • Operating schedule
  • Available fuel gas
  • Site elevation and ambient conditions
  • Materials requirements
  • Instrumentation and controls
  • Code requirements
  • Permit or monitoring requirements

Vapor Flow Rate

Vapor flow rate affects burner sizing, combustion chamber volume, stack design, controls, and piping. Flow may vary with gas throughput, glycol circulation rate, amine circulation rate, regeneration conditions, stripping gas use, and operating mode.

Combustion Chamber

Combustion chamber design considers residence time, temperature, mixing, refractory lining, access, operating environment, and the characteristics of the vapor stream. The required design basis should be set by project conditions and applicable requirements.

Burner and Controls

The burner system must be selected for the vapor stream and supplemental fuel requirements. Controls may include automatic ignition, flame detection, temperature monitoring, alarms, shutdowns, and integration with the associated dehydration or amine unit.

Materials

Materials selection depends on temperature, corrosion potential, acid gas content, sulfur compounds, weather exposure, and customer specifications. Some applications may require special consideration for stack materials, refractory systems, or sour service.

Fuel Consumption

Fuel consumption depends on vapor flow rate, heating value, target operating temperature, burner turndown, heat losses, and operating schedule. It should be evaluated during design rather than assumed from a generic value.

Alternatives and Complementary Controls

Thermal oxidizers are one possible emissions control approach. Other options may be considered depending on the vapor stream, facility requirements, and economics.

Potential alternatives or complementary systems may include:

  • Condensers
  • Vapor recovery units
  • Flares
  • Process changes
  • Reduced circulation rates where appropriate
  • Other permit-approved control devices

Each option has tradeoffs. A condenser may recover liquids but requires cooling and liquid handling. A vapor recovery unit may reduce emissions but adds compression and maintenance. A flare may be appropriate in some cases but may not provide the same monitoring or enclosure characteristics as a thermal oxidizer. The correct approach depends on project-specific requirements.

Working With QB Johnson on Thermal Oxidizer Applications

QB Johnson designs and fabricates thermal oxidizers for gas conditioning and natural gas processing applications. Thermal oxidizers may be supplied as standalone equipment or integrated with TEG dehydration units, amine treating units, or modular gas processing packages.

 

Project review typically starts with the gas analysis, vapor stream data, equipment lineup, operating conditions, site requirements, and applicable project specifications. From there, the thermal oxidizer package can be designed around vapor flow, combustion requirements, instrumentation, controls, fabrication requirements, and documentation needs.

 

QB Johnson can support equipment design, ASME-code fabrication where applicable, QA/QC, documentation, startup support, and spare parts support. When a project calls for one, request a quote for a thermal oxidizer.